ETHENE, HOMOPOLYMER SDS
SECTION 1: Identification of the substance/mixture and of the company/undertaking
Product identifier
- Product name： ETHENE, HOMOPOLYMER
- CAS： 9002-88-4
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses： For R&D use only. Not for medicinal, household or other use.
- Uses advised against： none
Company Identification
- Company：Chemicalbook.in
- Address：5 vasavi Layout Basaveswara Nilayam Pragathi Nagar Hyderabad, India -500090
- Telephone：+91 9550333722
SECTION 2: Hazards identification
Classification of the substance or mixture
Not classified.
GHS label elements, including precautionary statements
- Signal word No signal word
none
none
none
none
none
Other hazards which do not result in classification
no data available
SECTION 3: Composition/information on ingredients
Substance
- Chemical name: ETHENE, HOMOPOLYMER
- Common names and synonyms: ETHENE, HOMOPOLYMER
- CAS number: 9002-88-4
- EC number: 618-339-3
- Concentration: 100%
SECTION 4: First aid measures
Description of necessary first-aid measures
Fresh air, rest.
Remove contaminated clothes. Rinse and then wash skin with water and soap.
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
Rinse mouth with water. Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a doctor or Poison Control Center immediately.
Most important symptoms/effects, acute and delayed
no data available
Indication of immediate medical attention and special treatment needed, if necessary
no data available
SECTION 5: Firefighting measures
Suitable extinguishing media
Use dry chemical, carbon dioxide or alcohol-resistant foam.
Specific hazards arising from the chemical
Combustible. Gives off irritating or toxic fumes (or gases) in a fire. Finely dispersed particles form explosive mixtures in air.
Special protective actions for fire-fighters
Use water spray, powder, foam, carbon dioxide.
SECTION 6: Accidental release measures
Personal precautions, protective equipment and emergency procedures
Sweep spilled substance into covered suitable, labelled containers. If appropriate, moisten first to prevent dusting. Personal protection: particulate filter respirator adapted to the airborne concentration of the substance.
Environmental precautions
Prevent further spillage or leakage if it is safe to do so. Do not let the chemical enter drains. Discharge into the environment must be avoided.
Methods and materials for containment and cleaning up
Collect and arrange disposal. Keep the chemical in suitable and closed containers for disposal. Remove all sources of ignition. Use spark-proof tools and explosion-proof equipment. Adhered or collected material should be promptly disposed of, in accordance with appropriate laws and regulations.
SECTION 7: Handling and storage
Precautions for safe handling
NO open flames. Closed system, dust explosion-proof electrical equipment and lighting. Prevent deposition of dust. Handling in a well ventilated place. Wear suitable protective clothing. Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Use non-sparking tools. Prevent fire caused by electrostatic discharge steam.
Conditions for safe storage, including any incompatibilities
Separated from incompatible materials. See Chemical Dangers.
SECTION 8: Exposure controls/personal protection
Control parameters
| Component | ETHENE, HOMOPOLYMER | |||
|---|---|---|---|---|
| CAS No. | 9002-88-4 | |||
| Limit value - Eight hours | Limit value - Short term | |||
| ppm | mg/m3 | ppm | mg/m3 | |
| People's Republic of China | ? | 5 (1) | ? | ? |
| Remarks | ||||
| People's Republic of China | (1) Inhalable fraction | |||
no data available
Appropriate engineering controls
Ensure adequate ventilation. Handle in accordance with good industrial hygiene and safety practice. Set up emergency exits and the risk-elimination area.
Individual protection measures, such as personal protective equipment (PPE)
Wear safety goggles.
Wear fire/flame resistant and impervious clothing. Handle with gloves. Gloves must be inspected prior to use. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
Avoid inhalation of dust.
no data available
SECTION 9: Physical and chemical properties and safety characteristics
-
Physical state：
WHITE SOLID IN VARIOUS FORMS.
-
Colour：
no data available
-
Odour：
no data available
-
Melting point/freezing point：
85-140°C
-
Boiling point or initial boiling point and boiling range：
no data available
-
Flammability：
no data available
-
Lower and upper explosion limit/flammability limit：
no data available
-
Flash point：
341°C
-
Auto-ignition temperature：
330-410°C
-
Decomposition temperature：
no data available
-
pH：
no data available
-
Kinematic viscosity：
no data available
-
Solubility：
no data available
-
Partition coefficient n-octanol/water：
no data available
-
Vapour pressure：
no data available
-
Density and/or relative density：
0.94g/mLat 25°C
-
Relative vapour density：
no data available
-
Particle characteristics：
no data available
SECTION 10: Stability and reactivity
Reactivity
no data available
Chemical stability
no data available
Possibility of hazardous reactions
Dust explosion possible if in powder or granular form, mixed with air.Decomposes on heating. This produces toxic and irritating fumes. This generates fire and explosion hazard. Reacts violently with fluorine. Reacts with strong acids and strong oxidants.
Conditions to avoid
no data available
Incompatible materials
no data available
Hazardous decomposition products
no data available
SECTION 11: Toxicological information
Acute toxicity
- Oral: no data available
- Inhalation: no data available
- Dermal: no data available
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
no data available
Reproductive toxicity
no data available
STOT-single exposure
no data available
STOT-repeated exposure
no data available
Aspiration hazard
A nuisance-causing concentration of airborne particles can be reached quickly, especially if powdered.
SECTION 12: Ecological information
Toxicity
- Toxicity to fish: no data available
- Toxicity to daphnia and other aquatic invertebrates: no data available
- Toxicity to algae: no data available
- Toxicity to microorganisms: no data available
Persistence and degradability
no data available
Bioaccumulative potential
no data available
Mobility in soil
no data available
Other adverse effects
no data available
SECTION 13: Disposal considerations
Disposal methods
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
SECTION 14: Transport information
UN Number
ADR/RID: Not dangerous goods. (For reference only, please check.)
IMDG: Not dangerous goods. (For reference only, please check.)
IATA: Not dangerous goods. (For reference only, please check.)
UN Proper Shipping Name
ADR/RID: Not dangerous goods. (For reference only, please check.)
IMDG: Not dangerous goods. (For reference only, please check.)
IATA: Not dangerous goods. (For reference only, please check.)
Transport hazard class(es)
ADR/RID: Not dangerous goods. (For reference only, please check.)
IMDG: Not dangerous goods. (For reference only, please check.)
IATA: Not dangerous goods. (For reference only, please check.)
Packing group, if applicable
ADR/RID: Not dangerous goods. (For reference only, please check.)
IMDG: Not dangerous goods. (For reference only, please check.)
IATA: Not dangerous goods. (For reference only, please check.)
Environmental hazards
ADR/RID: No
IMDG: No
IATA: No
Special precautions for user
no data available
Transport in bulk according to IMO instruments
no data available
SECTION 15: Regulatory information
Safety, health and environmental regulations specific for the product in question
SECTION 16: Other information
Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/
Other Information
LDPE means Polyethylene with low density; HDPE means Polyethylene with high density.Physicochemical properties vary depending upon the molecular mass.Thermal degradation starts at 290°C.The PE products are available in large selection of various forms, due to additives used in the manufacture.The additives can influence the physical and toxicological properties of this substance.