Isopropyl acetate SDS
SECTION 1: Identification of the substance/mixture and of the company/undertaking
Product identifier
- Product name： Isopropyl acetate
- CAS： 108-21-4
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses： For R&D use only. Not for medicinal, household or other use.
- Uses advised against： none
Company Identification
- Company：Chemicalbook.in
- Address：5 vasavi Layout Basaveswara Nilayam Pragathi Nagar Hyderabad, India -500090
- Telephone：+91 9550333722
SECTION 2: Hazards identification
Classification of the substance or mixture
Flammable liquids, Category 2
Eye irritation, Category 2
Specific target organ toxicity – single exposure, Category 3
GHS label elements, including precautionary statements
-
Pictogram(s)
- Signal word Danger
H225 Highly flammable liquid and vapour
H319 Causes serious eye irritation
H336 May cause drowsiness or dizziness
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P240 Ground and bond container and receiving equipment.
P241 Use explosion-proof [electrical/ventilating/lighting/...] equipment.
P242 Use non-sparking tools.
P243 Take action to prevent static discharges.
P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
P264 Wash ... thoroughly after handling.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P271 Use only outdoors or in a well-ventilated area.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse affected areas with water [or shower].
P370+P378 In case of fire: Use ... to extinguish.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P319 Get medical help if you feel unwell.
P403+P235 Store in a well-ventilated place. Keep cool.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents/container to an appropriate treatment and disposal facility in accordance with applicable laws and regulations, and product characteristics at time of disposal.
Other hazards which do not result in classification
no data available
SECTION 3: Composition/information on ingredients
Substance
- Chemical name: Isopropyl acetate
- Common names and synonyms: Isopropyl acetate
- CAS number: 108-21-4
- EC number: 203-561-1
- Concentration: 100%
SECTION 4: First aid measures
Description of necessary first-aid measures
Fresh air, rest. Refer for medical attention.
Remove contaminated clothes. Rinse skin with plenty of water or shower.
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
Rinse mouth. Do NOT induce vomiting. Rest. Refer for medical attention .
Most important symptoms/effects, acute and delayed
Vapors irritate eyes and respiratory tract; high concentrations can be anesthetic. Liquid irritates eyes but causes no serious injury; may cause dermatitis; no serious effects if swallowed. (USCG, 1999)
Indication of immediate medical attention and special treatment needed, if necessary
For basic treatment: Establish a patent airway. Suction if necessary. Watch for signs of respiratory insufficiency and assist ventilations if necessary. Administer oxygen by nonrebreather mask at 10 to 15 L/min. Monitor for pulmonary edema and treat if necessary . Monitor for shock and treat if necessary . For eye contamination, flush eyes immediately with water. Irrigate each eye continuously with normal saline during transport . Do not use emetics. For ingestion, rinse mouth and administer 5 mL/kg up to 200 mL of water for dilution if the patient can swallow, has a strong gag reflex, and does not drool. Administer activated charcoal . Esters and related compounds
SECTION 5: Firefighting measures
Suitable extinguishing media
Extinguish with dry chem, /alcohol/ foam, or carbon dioxide. Water may be ineffective. Cool exposed containers with water.
Specific hazards arising from the chemical
Excerpt from ERG Guide 129 [Flammable Liquids (Water-Miscible / Noxious)]: HIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks). Vapor explosion hazard indoors, outdoors or in sewers. Those substances designated with a (P) may polymerize explosively when heated or involved in a fire. Runoff to sewer may create fire or explosion hazard. Containers may explode when heated. Many liquids are lighter than water. (ERG, 2016)
Special protective actions for fire-fighters
Use alcohol-resistant foam, foam, powder, carbon dioxide, fine water spray. In case of fire: keep drums, etc., cool by spraying with water.
SECTION 6: Accidental release measures
Personal precautions, protective equipment and emergency procedures
Remove all ignition sources. Evacuate danger area! Consult an expert! Personal protection: filter respirator for organic gases and vapours adapted to the airborne concentration of the substance. Do NOT wash away into sewer. Do NOT let this chemical enter the environment. Collect leaking liquid in sealable containers. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations.
Environmental precautions
Personal protection: filter respirator for organic gases and vapours adapted to the airborne concentration of the substance. Collect leaking and spilled liquid in sealable glass containers as far as possible. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations.
Methods and materials for containment and cleaning up
1. Remove all ignition sources. 2. Ventilate area of spill or leak. 3. For small quantities, absorb on paper towels. Evaporate in a safe place (such as a fume hood). Allow sufficient time for evaporating vapors to completely clear the hood ductwork. Burn the paper in a suitable location away from combustible materials. Large quantities can be collected and atomized in a suitable combustion chamber.
SECTION 7: Handling and storage
Precautions for safe handling
NO open flames, NO sparks and NO smoking. Closed system, ventilation, explosion-proof electrical equipment and lighting. Do NOT use compressed air for filling, discharging, or handling. See Chemical Dangers Handling in a well ventilated place. Wear suitable protective clothing. Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Use non-sparking tools. Prevent fire caused by electrostatic discharge steam.
Conditions for safe storage, including any incompatibilities
Fireproof. Separated from oxidants. Cool.STORAGE TANKS ... SHOULD BE SITUATED IN A MOUNDED COMPOUND CONSTRUCTED TO RETAIN MAX QUANTITY OF LIQUID THAT COULD ESCAPE FROM TANKS; DRUMS & OTHER SMALLER RECEPTACLES ... SHOULD BE KEPT IN STOREROOM OF FIRE-RESISTANT CONSTRUCTION WITH MOUNDED & RAMPED DOORWAY TO PREVENT ESCAPE OF SPILT LIQUID. ESTERS
SECTION 8: Exposure controls/personal protection
Control parameters
TLV: 100 ppm as TWA; 150 ppm as STEL.MAK: 420 mg/m3, 100 ppm; peak limitation category: I(2); pregnancy risk group: C
no data available
Appropriate engineering controls
Ensure adequate ventilation. Handle in accordance with good industrial hygiene and safety practice. Set up emergency exits and the risk-elimination area.
Individual protection measures, such as personal protective equipment (PPE)
Wear safety spectacles.
Protective gloves.
Use ventilation, local exhaust or breathing protection.
no data available
SECTION 9: Physical and chemical properties and safety characteristics
-
Physical state：
Isopropyl acetate is a clear colorless liquid. Flash point 40°F. Vapors are heavier than air. Contact with the material may irritate skin, eyes or mucous membranes. May be toxic by ingestion, inhalation and skin absorption. Used as a solvent.
-
Colour：
Water-white liquid
-
Odour：
Aromatic
-
Melting point/freezing point：
-73.4°C
-
Boiling point or initial boiling point and boiling range：
85-91°C(lit.)
-
Flammability：
Class IB Flammable Liquid: Fl.P. below 73°F and BP at or above 100°F.
-
Lower and upper explosion limit/flammability limit：
Lower: 1.8% by vol @ 38 deg C; Upper: 8% by vol
-
Flash point：
4°C
-
Auto-ignition temperature：
894°F
-
Decomposition temperature：
no data available
-
pH：
no data available
-
Kinematic viscosity：
0.49 CENTIPOISE @ 25 DEG C
-
Solubility：
1 to 10 mg/mL at 68° F (NTP, 1992)
-
Partition coefficient n-octanol/water：
log Kow = 1.02
-
Vapour pressure：
47 mm Hg ( 20 °C)
-
Density and/or relative density：
0.872g/mLat 25°C(lit.)
-
Relative vapour density：
3.5 (vs air)
-
Particle characteristics：
no data available
SECTION 10: Stability and reactivity
Reactivity
Reacts violently with oxidizing materials. Attacks many plastics.
Chemical stability
no data available
Possibility of hazardous reactions
KEEP AWAY FROM HEAT & OPEN FLAME ... Dangerous fire hazard when exposed to heat, flame, or oxidizers. Moderatedly explosive when exposed to heat or flame.The vapour is heavier than air and may travel along the ground; distant ignition possible.ISOPROPYL ACETATE is an ester. Esters react with acids to liberate heat along with alcohols and acids. Strong oxidizing acids may cause a vigorous reaction that is sufficiently exothermic to ignite the reaction products. Heat is also generated by the interaction of esters with caustic solutions. Flammable hydrogen is generated by mixing esters with alkali metals and hydrides. This compound can react vigorously with nitrates, strong oxidizers, strong alkalis and strong acids. This chemical may also attack some forms of rubber, plastics and coatings. (NTP, 1992).
Conditions to avoid
no data available
Incompatible materials
Can react vigorously with oxidizing materials.
Hazardous decomposition products
no data available
SECTION 11: Toxicological information
Acute toxicity
- Oral: LD50 Rat oral 3.0 g/kg From table
- Inhalation: no data available
- Dermal: no data available
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
no data available
Reproductive toxicity
no data available
STOT-single exposure
The substance may be irritating to the eyes, skin and respiratory tract. Exposure far above the OEL could cause lowering of consciousness.
STOT-repeated exposure
The substance defats the skin, which may cause dryness or cracking.
Aspiration hazard
A harmful contamination of the air can be reached rather quickly on evaporation of this substance at 20°C.
SECTION 12: Ecological information
Toxicity
- Toxicity to fish: no data available
- Toxicity to daphnia and other aquatic invertebrates: no data available
- Toxicity to algae: no data available
- Toxicity to microorganisms: no data available
Persistence and degradability
A screening test using an activated mixed microbial sewage inoculum indicated that isopropyl acetate had a 5 day BOD of 38%(1). Isopropyl acetate, at an initial concn of 0.4-3.2 ug/l, had a 52.3% 5 day BOD when incubated with an acclimated mixed microbial culture(2). In a screening test using a settled sewage seed, 2.5 ppm isopropyl acetate was found to have a 5 day BOD of 12.7%, which increased to 40% after 10 days and 49.1% after 40 days(3). Isopropyl acetate was determined to have a 5 day BOD of 61% using a settled domestic wastewater seed, and BOD's of 72%, 74% and 76% after 10, 15 and 20 days, respectively(4). When the same inoculum was added to synthetic sea water, the 5, 10, 15 and 20 day BOD's were 14%, 39%, 43%, 49%, respectively(4).
Bioaccumulative potential
An estimated BCF of 2 was calculated for isopropyl acetate(SRC), using a water solubility of 29,000 mg/l(1,SRC) and a regression-derived equation(2). According to a classification scheme(3), this BCF suggests that bioconcentration in aquatic organisms is low(SRC).
Mobility in soil
The Koc of isopropyl acetate is estimated as approximately 15(SRC), using a measured water solubility of 29,000 mg/l(1) and a regression-derived equation(2,SRC). According to a classification scheme(3), this estimated Koc value suggests that isopropyl acetate is expected to have very high mobility in soil(SRC).
Other adverse effects
no data available
SECTION 13: Disposal considerations
Disposal methods
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
SECTION 14: Transport information
UN Number
ADR/RID: UN1220 (For reference only, please check.)
IMDG: UN1220 (For reference only, please check.)
IATA: UN1220 (For reference only, please check.)
UN Proper Shipping Name
ADR/RID: ISOPROPYL ACETATE (For reference only, please check.)
IMDG: ISOPROPYL ACETATE (For reference only, please check.)
IATA: ISOPROPYL ACETATE (For reference only, please check.)
Transport hazard class(es)
ADR/RID: 3 (For reference only, please check.)
IMDG: 3 (For reference only, please check.)
IATA: 3 (For reference only, please check.)
Packing group, if applicable
ADR/RID: II (For reference only, please check.)
IMDG: II (For reference only, please check.)
IATA: II (For reference only, please check.)
Environmental hazards
ADR/RID: No
IMDG: No
IATA: No
Special precautions for user
no data available
Transport in bulk according to IMO instruments
no data available
SECTION 15: Regulatory information
Safety, health and environmental regulations specific for the product in question
SECTION 16: Other information
Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/
Other Information
Do NOT take working clothes home.